Parts

- Chromoly steel with black oxide finish - 1.37" x 24tpi right hand thread - Requires a cog lockring (sold separately) - Compatible with 1/8-inch chains

The BB5 offers our Tri-Align Caliper Positioning System, tool-free pad replacement, a melt-forged body and an inboard pad adjustment knob. One try and you'll wonder if the BB5's are really entry-level brakes. - Mechanical simplicity

- Noodle/Boot completely seal brake cable, upgrades most linear brakes

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Clean up your handlebar with Avid's MatchMaker X clamp. It combines mounts for your SRAM shifters and Avid brake levers into one simple, sleek unit so you can shed grams and keep your bars nice and tidy. You can also integrate RockShox's XLoc remote (sold separately) for maximum convenience and ease of use.

Box One™ fork adapters let you run standard "Male" 10mm (3/8" axles) in a fork designed for 20mm axles. - Material 6061-T6 Aluminum

All Box stems are engineered and crafted using our Oversized Technology. As we follow the load paths down the handlebars we have focused our attention on the stem-to-bar interface. Since the Oversized handlebars have an increased wall thickness and tube diameter in this sector we have reciprocated with an augmented stem interface with greater surface area. We’ve done this by moving material from low stress areas. This has greatly minimized twist and contributed to responsiveness. As the stem in mated with the handlebars we have contributed to increased pedaling stiffness by providing a backstop to the “lifting” phenomenon. There is no point pushing hard on your pedals if you can’t pull up on your handlebars and deliver that power. Power can easily be lost to handlebar-to-stem deflection and the consequences can be poor power delivery and steering control. When combined with Box’s other Oversized components, you’ll experience heightened responsiveness and reduced latency. Key differences: In this particular model stem we’ve tailored the Oversized strategy to favor utility and access. The geometry has been altered to allow for easy handlebar removal while at the same time scavenging material from low stress zones. Ideal for those who don’t want to compromise on user experience to gain performance. These stems are engineered for the larger-sized racers.

The Box Three E-Bike Cassette offers high gears with more teeth to withstand the rigors of modern E-Bike riding. Adding an extra tooth to each of the three highest gears provides increased durability and decreased wear by distributing the load over a larger area! The Box Three E-bike cassette draws from both of its Box One and Box Two siblings to create a sensible all-rounder. All cogs are stamped from steel and subsequently, the larger ones are pinned to steel spiders. The main difference here versus Box Two is the use of additional weight-reducing holes on the cogs. FEATURES - Our Best All-Rounder Cassette - Steel Stamped Cogs - Steel Stamped Spiders - Ultra-Wide Ratio with Consistent Progression COMPATIBILITY - Box One Prime 9 Chain 126L DLC Black - Box Two Prime 9 126 Link Chain Nickel - Box Three Prime 9 126 Link Chain Polished - Box One Prime 9 Rear Derailleur - Box Two Prime 9 X-Wide Rear Derailleur Black - Box Three Prime 9 X-Wide Rear Derailleur Black - Box One Prime 9 Single Shifter Black - Box Two Prime 9 Single Shifter Black - Box Three Prime 9 Single Shifter Black

These extremely durable pedals are constructed of a nylon composite thermoplastic body and feature eight removable steel M3 pins per side for superior grip. - One sealed bearing is paired with a long-lasting DU sleeve in each pedal for an impressively smooth interface - Chromoly steel spindle for strength - Spindle size: 9/16-inch

- Designed for linear pull & mechanical disc brakes - Aluminum construction - 2.5 finger - 22.2mm (7/8-inch) clamp - Left/Right: Right - Reach adjust and return spring - 88g each

Nylo-Comp Pedals feature a one-piece resin body, molded pin design, and chromoly spindle. - Loose ball bearings - 375g/pair

- Chromoly construction - Classic BMX Lay-back design - Material: Cro-Mo

Forged alloy platform pedals with a hardened chromoly spindle. - Molded pins - Size: 9/16-inch

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 40mm (1-1/2") tapered steerer tubes - Lightweight aluminum construction

Cane Creek headsets with Hellbender stainless steel bearings with increased sealing elements and more grease in relation to the comparable 110 bearing. - Designed to bridge the gap between the 40-series and 110-series headsets

The Hellbender70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

The Hellbender 70 bottom bracket utilizes a bearing made of 440C stainless steel, providing exceptional ride quality and reliability. The stainless steel bearing in the Hellbender 70 strikes a perfect balance between value and lasting performance. - 440C stainless steel bearings, dual lip seal, marine grease - Machined aluminum cups

Compatibility: Shimano XTR, XT, SLX, M985, M785, M666, S700 2011+

Compatibility: Shimano Ultegra, Br-GRES805, BR-GRE505.

Compatibility: Shimano XTR 2007 (M965-M966), Saint, Deore LX 2005 Pad Material: Organic

Compatibility: Avid Elixir 1, 3, 5, Elixir R, Elixir CR, SRAM XX, X0.

Compatibility: Shimano Deore (BR-M515, M475, M525, M465, M495) Auriga Comp, Aquila Clarks S2

Includes all hardware Bolt-on style mount Brand Compatibility: Shimano Length of Pad: 52mm Compound: All Weather

E-Bike specific rotor constructed from high-quality 120 CR grade steel 2.3mm thickness for exceptional strength, durability and heat management

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

Crank Brothers' Eggbeaters are 4-sided, which makes them super easy to enter and exit. Their open design makes them shed mud and debris quickly, and these pedals feature 6-degrees of knee-friendly float. The Eggbeater 1s feature chromoly axles, stainless-steel springs, and steel bodies.

Size specific magnesium platform pedal provides optimal shoe/pedal interface. Details - Magnesium pedal body for weight reduction - Optimal surface area - Minimal body profile - 16mm thin - Concave pin profile & 10 adjustable pins per side for grip - Premium bearings & seal system - Stamp small recommended for shoe sizes: 5-10 (us) // 37-43 (eu) - Stamp large recommended for shoe sizes: 10-15 (us) // 43-49 (eu) - Serviceable, pedal refresh kit found here Specs - Adjustable pins: 10 per side - Body material: AM60B Magnesium Alloy - Endcap: T15 - Footprint: 114mm x 111mm - Inner bearing type: Igus Bearing - Max rider weight: No restriction - Outer bearing type: Double Cartridge Bearing - Shoe size: US 10-15 // EU 43-49 - Spindle material: Forged SCM 415 Chromoly Steel - Warranty: 5 years - Weight: 386g per pair

Crank Brothers' Candy 3 pedals combine 4-sided cages for super-easy entry/exit with CNC'd aluminum platforms for low weight, great foot stability, and on-trail durability. The Candy 3s feature chromoly axles, stainless steel springs, CNC machined aluminum wings, and an open design that sheds mud fast, making them ideal for sloppy conditions and cyclocross. They're also enhanced with inner needle bearings and water-tight internals for consistently smooth pedaling.

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 18307 Bearing

Parts for repair and maintenance of DT Swiss hubs. - DT Swiss 240 Disc Ring Nut

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 6902 Bearing

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 6802 Bearing

Bearings for maintaining and rebuilding DT Swiss hubs. - DT Swiss 6803 Bearing

A five-piece IGUS bushing spacer kit for mounting rear shocks. - Compatible with x eyelet shocks using IGUS bushings mounted in the shock eyelet - Select the correct hardware kit for your mounting bolt diameter (e.g. 6mm, 8mm) and frame mount width (e.g. 22mm, 24mm)

- Clamps to a threadless steerer, offers up to 3-1/4" stem height increase - Forged 6061 aluminum - Threaded alloy top cap

- Clamps to a threadless steerer - Offers up to 4-1/2" stem height increase - Forged 6061-aluminum provides extra strength - Machined aluminum top cap is threaded, providing easy installation

- Clamps to a threadless steerer - Offers up to 4-1/2" stem height increase - Forged 6061-aluminum provides extra strength - Machined aluminum top cap is threaded, providing easy installation

Dimension Combo Pedal Sets are assembled with size large toe clips, straps and reflectors. - Pedal Body Material: Plastic - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 475g

Dimension Stem Column Adaptors - Total quill length 180mm - Measurement from minimum insertion to top of steerer adaptor is 118mm - Alloy - Quill insertion diameter: 1-inch

Dimension 31.8 Stems are fully forged 6061-T6 aluminum stems that have a 4-bolt handlebar clamp. - 31.8mm can be used with 26.0 bars with additional shim (SM5317) - Dimension stems are not intended for use with carbon handlebars or carbon steer tubes - Weight: 130g-180g

Dimension Combo Pedal Sets are assembled with size large toe clips, straps and reflectors. - Pedal Body Material: Aluminum - Pedal Spindle: 9/16-inch - Pedal Type: Toe Clip Compatible - Spindle Material: Chromoly Steel - Weight: 520g

For cross country and all-mountain riding, Dimension Trail Stems provide a broad array of sizing options, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes

For cross country and all-mountain riding, Dimension Trail Stems provide a broad array of sizing options, rigorously tested to ISO 4210 Mountain standards. - Constructed with AL-6061-T6 aluminum - Shot-peened finish - Dimension stems are not intended for use with carbon handlebars or carbon steerer tubes

Dimension Freewheels are excellent drivetrain component replacements. With smooth shifting performance and durable construction, they'll help breathe new life into older bikes. - A must-have in any bicycle service department - One-piece design - Shimano index compatible - Works with most friction shifters - Suitable for use with e-bike drivetrains

A race-proven handlebar, the M9 bar is ENVE's dedicated downhill option. Designed around a 31.8mm clamp diameter and a downhill-focused flex profile, this bar’s celebrated ride feel defined the potential of a DH carbon fiber bar and realigned performance expectations. The M9 bar features 8-degree backsweep and 4-degree upsweep. - Material: Carbon - Weight: 245g (30mm rise); 265g (50mm rise) - Bar Width (Max): 810mm - Bar Width (Min): 780mm - Clamp Diameter: 31.8mm - Backsweep: 8 Degrees - Upsweep: 4 Degrees - Torque Spec: Face Plate: 5.5Nm - Torque Spec: Controls: 5.5Nm

The ESI Extra Chunky grips are the thickest available. 80 grams, standard grip length - 5 1/8", installed DIA. 34 mm, weight plus or minus 5%, 1 set of bar plugs included. - 80 Grams - Standard Grip Length – 5 1/8" - Installed Dia. 34mm - Weight plus or minus 5% - Made for 22mm bars (can fit applications down to 19mm) - Bar Plugs included - *Install Bar Plugs first for the protection of grips and ease of installation

ABI Headset Bearing for new builds or replacements.

ABI Headset Bearing for new builds or replacements.

- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity

ABI Headset Bearing for new builds or replacements.

The GA2 All-Mountain / Gravity grip has superb tactile feel thanks to a super-soft, UV stable rubber compound exclusively developed and manufactured in Germany for Ergon. The ergonomic shape requires less rider grip pressure while specific grip zones – matched to the shape of the hand – increase tactile feedback and traction. The inner construction varies in thickness to allow greater damping, which results in less ulna nerve stress and decreased arm pump. The inboard aluminum clamp allows even more grip area at the end of the bars. The gripset is lock-on and carbon bar friendly. - Uses: mountain bike, all-mountain, freeride, dirt - Clamp: aluminium, black anodized

Combining ergonomics, function, and sustainability, the GP1 BioKork has been a top-rated grip and a consumer favorite. The grip is made from 40% cork, sourced from sustainable forests in Portugal. This green, sustainable theme is echoed throughout the complete construction of the grip with an inner core made of a reinforced plastic utilizing natural fibers which makes up 20% of its mass. - Carbon bar compatible - Clamp: cold forged aluminium – 100% recyclable - Uses: mountain bike, touring, commuting

- Shimano SPD-SL-style - Engineered thermoplastic injection body - Anti-slip walk pads - Fixed position with no float

- Shimano SPD-SL-style - Engineered thermoplastic injection body - Weight of 24 grams per cleat - 4.5-degree floating arc

Pedal built with quality materials. It features a strong, aluminum body, and a Cr-Mo axle on a slimline dual bearing system. - LSL bushing & sealed bearings - Tension gauge - Aluminum Body with CNC-Machined chromoly spindle - Includes E-RSL1 SPD-SL Style Cleats and mounting hardware

Replacement headset bearings from FSA. - Compatible with most Trek MTB integrated headset systems - Sealed bearing for long life - Compatible with Knock Block Headsets

FSA bearings that set directly into the frame without the use of pressed in cups. - 36/45 degrees is Cane Creek-compatible - 45/45 degrees is Campagnolo-compatible

FSA ACR (Aerodynamic Cable Routing) Headsets are suitable for both road and MTB riding styles and feature angular contact bearings. - A fully integrated cable routing - No rotation limit - ACR top cover - Angular contact bearing - Specific frame required - 1.5" headtube - 36°/45° ACB - For 55.8mm OD headtube - For 1-1/8" to 1.5" tapered fork - Stack height 10.4+0.5=10.9

Shifting performance has helped Full Speed Ahead to become a world leader for high-end chainrings. No one studies the design and manufacturing of each system, and each tooth, as carefully as we do. Our dedication shows in every revolution of the crank, and every perfect shift achieved. To meet or exceed the needs of any drivetrain, Full Speed Ahead has developed sophisticated design, testing and manufacturing protocols. This allows Full Speed Ahead to match your needs as perfectly as our chainrings match a chain. We offer more options, levels, and finishes than our competitors. We use the best materials available, imported from the USA, Europe, or sourced from our qualified vendors in Asia, to guarantee the durability, performance, and appearance will out-perform, and outlast the competition. Full Speed Ahead chainrings have powered multiple World, Tour de France, and Olympic champions, and will exceed your expectations. True value and performance are found in this FSA road chainring. It offers both long wear life and smooth shifting. - Stamped AL7075/T6 - N11 chainrings are compatible with all 10 speed drivetrains, and compatible with FSA, SRAM and Shimano 11-speed drivetrains - Ramped and pinned for excellent shifting - FSA 110 BCD - 4-Bolt - Material: Aluminum - Ring Position/Type: Inner

ISIS revolutionized bottom bracket spindles. Keep yours spinning smoothly with this Platinum ISIS Bottom Bracket from FSA. - Forged, hollow chromoly spindle with titanium nitride coating - Integrated, large ball bearing design - Cold-forged aluminum cups - Includes crank bolts